Engine Support Bars

Overview:
✔ Universal support for moving the engine towards the front or rear of the vehicle
✔ Connects the engine to the front subframe for controlled positioning
✔ Holds the engine against the resistance of the engine mounts
✔ Facilitates transmission, catalytic converter and exhaust system repairs
✔ Suitable for many VAG 6-speed manual and 6- or 7-speed DSG transmissions
✔ Universally usable on a wide range of vehicles
✔ For use as VAG T10235, T10533 and T50015

Overview:
✔ Supports engines and gearboxes during removal and installation
✔ Suitable for gearbox repairs and clutch replacement on front-wheel-drive vehicles
✔ Adjustable width: 1,120–1,450 mm
✔ Maximum load capacity: 300 kg
✔ Stable square steel-tube construction
✔ Sliding supports for adaptation to different vehicle types
✔ Slotted holes for flexible width adjustment
✔ Support hook with M24 × 3.0 threaded rod
✔ Includes one 900 mm support chain
✔ Rubber protectors safeguard the wing edges

Overview:
✔ Supports engines and gearboxes during removal and installation
✔ Enables front-axle removal without removing the complete powertrain
✔ Suitable for front- and rear-wheel-drive vehicles
✔ Supports gearbox repairs and clutch replacement on front-wheel-drive vehicles
✔ Adjustable width: 750–1,450 mm
✔ Maximum load capacity: 500 kg
✔ Stable square steel-tube construction
✔ M20 × 2.5 threaded support hooks
✔ Rubber protectors safeguard the wing edges
✔ Includes two 900 mm support chains

Overview:
✔ Supports engines and gearboxes during repair and installation work
✔ Extra-wide 1,700 mm design for modern and wider vehicles
✔ Wing-support width continuously adjustable from 750 to 1,650 mm
✔ Maximum load capacity: 500 kg
✔ Two M20 threaded hook rods with 1,000 mm support chains
✔ Pivoting wing supports adapt to different wing angles
✔ Fine lifting-height adjustment using T-handle lever nuts
✔ Rubber-protected feet and side protectors safeguard the wing edges
✔ Suitable for timing-belt, timing-chain, engine-mount, clutch, gearbox and subframe work

Overview:
✔ Converts the two-point engine support bridge, Item no. 120616, to four-point support
✔ Allows support on strut towers, the front lock carrier or longitudinal members behind the headlights
✔ Suitable for most passenger cars and light commercial vehicles
✔ Accommodates short vehicle fronts and steeply sloping wings
✔ Suitable for vehicles with plastic or non-load-bearing wings
✔ Extra-wide configuration for SUVs, larger vehicles and vans
✔ Compatible with engine support bridges up to approximately 65 × 85 mm beam dimensions
✔ Recommended minimum engine-bridge width: 160 cm
✔ Engine support bridge is not included

Overview:
✔ Securely supports engines and gearboxes during repair work
✔ Suitable for engine-mount removal and timing-belt or clutch replacement
✔ Stable square steel-tube construction
✔ Height-adjustable and lockable support feet and support pads
✔ Rotatable support hooks with handwheel height adjustment
✔ Sliding and lockable crossbeam and support hooks
✔ Non-slip rubber surfaces on the support pads
✔ Suitable for vehicles with steeply sloping wings
✔ Adjustable longitudinal beam: 690–1,050 mm
✔ Maximum distance between support hooks: 500 mm

Overview:
✔ Supports the engine during gearbox removal and installation
✔ Maximum load capacity: 500 kg
✔ Main bridge adjustable from 400 to 1,400 mm
✔ Additional crossbeam adjustable from 140 to 810 mm
✔ Stable construction made from square steel tubing
✔ Wide adjustment range in both length and width
✔ Rubber-covered support feet provide grip and protect contact surfaces
✔ Includes two threaded spindles with hooks
✔ Maintains access to components beneath the engine

Overview:
✔ Supports engines safely during and after gearbox removal
✔ Suitable for 2- and 3-point support configurations
✔ Maximum load capacity: 315 kg
✔ Adjustable crossbeam width: 1,000–1,550 mm
✔ Longitudinal support adjustable through 24 positions from 90 to 780 mm
✔ Supports positioned on the wing mounting flanges and, when required, the front lock carrier
✔ Variable suspension points for a wide range of vehicles
✔ Includes two engine-support cables

Overview:
✔ Securely supports engines during and after gearbox removal
✔ Four-point support helps prevent engine twisting and tilting
✔ Particularly suitable for vehicles with subframes
✔ Two adjustable longitudinal supports with rubber-protected feet
✔ Can also be used conventionally without the longitudinal supports
✔ Adjustable width up to 1,500 mm
✔ Longitudinal supports adjustable from 510 to 845 mm
✔ Maximum load capacity: 315 kg
✔ Includes two 530 mm chains with shackles

Overview:
✔ Supports transverse engines from beneath the vehicle
✔ Suitable for timing-belt, water-pump and tensioner work
✔ Leaves the upper engine compartment free from an obstructing support bridge
✔ Suitable for vehicles where an upper engine bridge is difficult to install
✔ Adjustable length from 620–900 mm
✔ Flexible support positioning with ball-jointed rubber feet
✔ Includes two hook-shaped and two flat support rods
✔ Maximum load capacity: 250 kg
✔ Fully galvanised construction
✔ Made in Germany

Overview:
✔ Professional engine support fixture for VW T4 transmission removal
✔ Suitable for VW T4 models with standard front end up to model year 1995
✔ Allows engine movement in all directions during gearbox removal
✔ Designed for 4-cylinder and 5-cylinder engines
✔ Simplifies removal and installation of engine and gearbox mounts
✔ Essential for clutch replacement and transmission service work
✔ Allows transmission removal without releasing torsion bars
✔ Used as VW 3184, 3227 and 3230
✔ Includes support blocks, cross member and mounting wedges

Overview:
✔ Designed for Volkswagen Transporter T4
✔ Supports the engine during transmission removal and installation
✔ For use with a suitable engine support bridge or crossbar
✔ Two adapters are required for supporting the engine
✔ One adapter is included
✔ Used as VAG/VW 10-222A/6

Overview:
✔ Adapter foot and longitudinal support for safely supporting the engine
✔ Suitable for VW Transporter T5, T5 Facelift and T6
✔ Optimised length for the different vehicle configurations
✔ Pivoting adapter foot fits both common lock-carrier and front-carrier designs
✔ Convertible between T5, T5 Facelift and T6 by repositioning the movable adapter
✔ Must be combined with a suitable engine support bridge, such as Item no. 120616
✔ Two adapters are required to support the engine
✔ One adapter is included

Overview:
✔ Extension for the engine support adapters Item no. 115401 as 10-222A/23
✔ Designed for Volkswagen Transporter T6
✔ Supports the engine, transmission and subframe during repair work
✔ Adapter feet are inserted into the existing crossmembers and secured with screws
✔ Allows use with a standard engine support bridge, such as Item no. 120616
✔ Can be used with the original VAG base tool as 10-222A/23
✔ Cannot be used without the required base adapter set